International Journal of Science and Research (IJSR)

International Journal of Science and Research (IJSR)
Call for Papers | Fully Refereed | Open Access | Double Blind Peer Reviewed

ISSN: 2319-7064


Downloads: 176 | Views: 342

Research Paper | Mechanical Engineering | India | Volume 8 Issue 3, March 2019 | Popularity: 6.6 / 10


     

Enhancement of Heat Transfer Coefficient in DPDGSAH having V Ribs with Symmetrical Numbers of Gaps in a Rectangular Duct: A Robust Design Approach

Jolly Lucas, Pooja Tiwari


Abstract: Enhancement of heat transfer coefficient has been carried out through a solar air heater (DPDGSAH) having artificially roughened V-type geometry with symmetrical gaps and then optimized by use of Robust design method. A L25 orthogonal array is used to optimize the geometry factors for the maximum thermal performance of the ribbed channel. Thermal performance concept includes maximization of heat transfer coefficient and its thermal efficiency. Maximization of heat transfer coefficient is taken as the criteria of optimization. The investigation encompassed Reynolds number (Re) ranging from 4000 to 12000, relative roughness pitch (P/e) values of 412, angle of attack () range of 300900, relative gap width (g/e) values of 15, Number of gaps (Ng) values of 15, and relative roughness height (e/D) values of 0.043. Results show that Reynolds Number (Re), relative roughness pitch (P/e), angle of attack () have the greatest influences parameters on maximization of heat transfer coefficient.


Keywords: V-Rib with symmetrical gaps, Taguchi method, ANOVA, Heat transfer coefficient


Edition: Volume 8 Issue 3, March 2019


Pages: 328 - 335



Make Sure to Disable the Pop-Up Blocker of Web Browser




Text copied to Clipboard!
Jolly Lucas, Pooja Tiwari, "Enhancement of Heat Transfer Coefficient in DPDGSAH having V Ribs with Symmetrical Numbers of Gaps in a Rectangular Duct: A Robust Design Approach", International Journal of Science and Research (IJSR), Volume 8 Issue 3, March 2019, pp. 328-335, https://www.ijsr.net/getabstract.php?paperid=ART20195896, DOI: https://www.doi.org/10.21275/ART20195896



Similar Articles

Downloads: 105

Research Paper, Mechanical Engineering, India, Volume 3 Issue 11, November 2014

Pages: 2865 - 2869

Dry Sliding Wear Behaviour of Al-Si-Ti Alloys Using Taguchi Method

Ganpat B. Jambukar, Dr. Y. R. Kharde

Share this Article

Downloads: 116

Research Paper, Mechanical Engineering, India, Volume 6 Issue 11, November 2017

Pages: 1833 - 1842

An Experimental Investigation and Optimization of Electrical Discharge Drilling for Small Hole Drilling with High Aspect Ratio

Ashok Kumar, Sandeep Kumar Rawal

Share this Article

Downloads: 117

Research Paper, Mechanical Engineering, India, Volume 4 Issue 1, January 2015

Pages: 2699 - 2702

Optimization of End Milling Parameters on Surface Roughness of Die Steel HCHCr by Taguchi Method

M. S. Harne, Ravikumar L. Shirsat

Share this Article

Downloads: 119 | Weekly Hits: ⮙1 | Monthly Hits: ⮙1

Research Paper, Mechanical Engineering, India, Volume 5 Issue 3, March 2016

Pages: 1988 - 1994

Optimization of Process Parameters of Friction Stirs Welding of Aluminum Alloys (6061) Using Taguchi Method

Siva Rama Krishna R, Pavan Kumar T

Share this Article

Downloads: 120

M.Tech / M.E / PhD Thesis, Mechanical Engineering, India, Volume 8 Issue 12, December 2019

Pages: 1622 - 1629

Some Investigations on Drilling of Aluminium Based Metal Matrix Composites

Vinodkumar M. Chandankar, Aarti A. Dyade

Share this Article
Top